The default IP should be 192.168.1.1 and your supposed to leave the Username blank and the Password is admin. This is all over google by the way. _____ R7000 Kong vpn 23550-R01 (Main Router) WRT610Nv2 converted E3000 vpnKong 21661 (RB) WRT600N v1.1 BS std-nokaid 13637(5Ghz CB)(2.4Ghz AP) WRT54G v5 BS micro 14684(RB)

Jul 19, 2016 · Now go to 192.168.1.1 (the DD-WRT default IP address) and you'll see the following. The DD-WRT default login details tend to match that of the router, but not only should you, but you will need to change this. That's it you're done with the DD-WRT firmware upgrade. DD-WRT e900 e1200 e2000 e2500 e3000 e4200 v24 sp2 Linksys wrt54g /gl/gs default root password DD-WRT default Password Default Web GUI URL Address : Default. The first field – Local IP address, that’s gonna be the IP address of our DD-WRT repeater. By default, it will be – 192.168.1.1. But that needs to be changed. The local IP address must be in the same IP pool range that our primary router has. And it must be in the range that the DHCP of the primary router is providing. How To Set Up A Repeater Bridge On Your DD-WRT Router. To begin, make sure that the main router has a 192.168.1.X subnet and leases a DHCP address in the same pool. The secondary router must be running DD-WRT. To ensure easy setup, always click Save and not Apply between steps. Reset to Factory Defaults on the secondary DD-WRT router. FAQ. Q: I want to use DD-WRT but do not know if my router is supported, where can I get this information? A: Please check the router database first. If the router is not listed, please follow the instructions for device detection to find out if router support is possible. That will get the DD-WRT Access Point up and running. If there is a need to open the Web interface, you can do so by typing in the IP Address that you had assigned earlier to the Access Point. Wrap Up. In conclusion, the DD-WRT Access Point can increase the wireless network coverage in your home or workplace.

Firmware: DD-WRT v3.0-r29440 std (04/11/16) Kernel: Linux 4.4.7-rc1 #604 SMP Mon Apr 11 05:42:18 CEST 2016 armv7l Status: ok Reset: yes (after flashing, reset to default settings) Errors: Limited Connectivity on the Virtual Guest AP (on wl0.1). Clients can connect to the AP, but its IP address is 169.254.x.y. DNSMasq seemingly fails to respond.

After installing DD-WRT Firmware you can access the DD-WRT Web-GUI using a web browser pointing to the same IP address as before you installed DD-WRT. These are some of the most common default IP addresses: 192.168.1.1 (most commonly used on Linksys and Asus), 192.168.2.1 (some Belkins), 192.168.11.1 (some Buffalos), 192.168.10.1 or 192.168.30 For example, if the router default address is 192.168.10.1, set the computer IP manually to 192.168.10.77 with 192.168.10.1 as the gateway. Power the router on with a continuous ping running in a command window: ping -t If you still receive no response, the IP address may have been changed from the default. Disconnect all Find the default login, username, password, and ip address for your Linksys DD-WRT router. You will need to know then when you get a new router, or when you reset your router. Firmware: DD-WRT v3.0-r29440 std (04/11/16) Kernel: Linux 4.4.7-rc1 #604 SMP Mon Apr 11 05:42:18 CEST 2016 armv7l Status: ok Reset: yes (after flashing, reset to default settings) Errors: Limited Connectivity on the Virtual Guest AP (on wl0.1). Clients can connect to the AP, but its IP address is 169.254.x.y. DNSMasq seemingly fails to respond.

Jul 19, 2016 · Now go to 192.168.1.1 (the DD-WRT default IP address) and you'll see the following. The DD-WRT default login details tend to match that of the router, but not only should you, but you will need to change this. That's it you're done with the DD-WRT firmware upgrade. DD-WRT e900 e1200 e2000 e2500 e3000 e4200 v24 sp2 Linksys wrt54g /gl/gs default root password DD-WRT default Password Default Web GUI URL Address : Default.